TL;DR: Ford heated wheels aren’t very warm. Splice a 1.5-2.2k resistor in-line with the wheel’s temperature sensor and boom: roasted. Pretty easy mod.
My last car (EV6 GTL) was the first I’ve owned with a heated steering wheel, and it was EXCELLENT. Absolutely cranked out power at obviously high temperature. It was lovely for recovering after a winter ocean swim, when your extremities are chilled to the bone. It seemed to me like it was open-loop controlled and just cranked out whatever power it was designed for. If it had active temperature control, the setpoint was quite high.
My new car (Mach-E Rally), not so much. It turns out this is pretty standard among Fords with heated steering wheels – they’re all closed-loop controlled, and all quite weak except for the initial turn-on that overshoots the setpoint by quite a lot. The net effect is that the wheel feels like it’s heating up nicely, but then settles to barely-noticeable – useful for preconditioning in the winter to avoid handling an icicle, but not at all useful for warming cold hands.
And there’s something to this: ForSCAN shows settings going back generations for the heated wheel set temperature, but the registers top out at 100F. The workshop documentation shows ranges right around 37C, which is basically just skin-warm!
Not knowing all of this, I actually brought my car to the dealership to have them take a look (among other issues), since it seemed to the touch like it was getting hot but then shutting off totally. The SA (correctly) informed me that it was actually normal, but for some reason they cleared all the troubleshooting steps and replaced the wheel anyway. Unfortunately, the new one was marginally colder!
Background Research
After some googling, I came across poster markboris’ work in this macheforum.com thread about the location of the temperature sensor, and how he typically moves it manually to a colder location on wheels he modifies. I also searched around for whether the temp setting could be modified in ForSCAN and found a number of threads like this one, which all conclude, basically, no – nobody’s quite sure how to do it on the newer Mach-E since the control module is different from older cars, and in the older cars, the setpoint can’t go higher than 100F anyway.
I also dug through the lemonmanual pages to figure out how to get TO the temp sensor wiring. The key takeaways here were:
- I’d need to pull off the airbag
- That wouldn’t require removing the entire wheel
- Removing the airbag, if there are no SRS faults, does NOT require powering down the car by disconnecting the battery – turning it off for >1min is sufficient
- I didn’t actually end up needing to unplug the airbag after moving it aside anyway, so no big deal.
Time to Mod
After some background research, I had a hunch that the temperature sensor would be a standard cheap NTC thermistor, in which case I could simply splice some additional resistance in-line with it to make the controller think the wheel is colder than it actually is. Previous efforts have focused on moving the thermistor to a colder location on the wheel, but that seemed more-invasive, more error-prone, and less-controllable to me.
I started by removing the airbag, which was quite easy with a catch: You release it by pushing a latching bar aside on the left side (with the wheel rotated 90* CW) and then on the right side (by turning it 90* CCW). But the driver monitoring camera is in the way of both!

Two things are unclear in this image: 1) the purple thing you’re pushing is a metal bar held in place by a metal spring, not a stiff plastic clip like most panels in the car. Merely pushing a screwdriver into the slot in the right spot with gentle pressure is enough to release it, and the airbag will pop free on that side. 2) you won’t be able to reach the driver in there in the first place if the driver monitoring camera is in the way. Get through that by grabbing it (gently) from either side, and lifting straight up. The entire top fascia of the steering column, held in place with one plastic clip on either side, pulls away. Then you can kind of just shove it out of the way however you need to fit the screw driver.
Here’s a photo of the latch once the airbag is pulled off, for reference. Latching bar circled in red, and the direction you push it with the screw driver in yellow (towards the center of the wheel). It moves with very little actual force.

Once you’re in the wheel, the mod zone is super obvious:

That brown 4-wire connector has red and black heavier wires for the heater, and green and orange wires for the thermistor. It’s retained in place with the white clip that press-fits in place and can easily be pried out with a screwdriver, giving you plenty of space to work on the wires.
I started by measuring the temp sensor at a few different temperatures – ambient, after it had been heated a little, and as it was cooling down somewhere in the middle, all in comparison to a thermocouple touching the surface of the wheel nearby.

The measurements weren’t terribly accurate, but they tell the story of a 10k NTC thermistor with beta of about 3500k. ChatGPT tells me that if I want to make the sensor read 40C when it’s really 50C, I want about an additional 1.5k in there.
Well, I had 1k easily on hand, so I spliced in some female Mini-PV/Dupont connectors and stuck that in between to test. It didn’t get hotter-enough for my taste. I couldn’t easily find 1.5k, so I yolo’d it with 2.2k. That got mighty hot. Possibly even too hot, but for now, that’s what lives in my wheel. I soldered the resistor to a pin header on each end for a decent connection, then instead of heatshrink which would have been tricky in the tight space, I just taped it all over with some Tessa fuzzy harness tape.

The most annoying part of the mod is that, to re-seat the airbag, you have to push it in, setting off the horn. And I did this mod at like 10pm. Whoops.
Now the money shots! Before: The bottom-center where the sensor is gets the hottest, at about 51C max before it settles down. The rest of the wheel hits a peak of ~44c, before settling down into steady state in the high-30s.

After. The first image shows peaks, right before the heating phase ends for the first cycle. The bottom center hits 63C this time, while the hottest point on the rest of the wheel is about 54C. ]

At this point, heating stops and the wheel cools off to a minimum of 55C on the sensor, and 43-47C elsewhere. Nice and toasty!

Thermal Video
The original videos the images above come from. Kind of boring unless you’re into that sort of thing.
Original wheel, unmodded. Hottest it ever gets is 49C at the sensor before settling down to around 40C, with the rest of the wheel in the mid-30s (skin temp)
New wheel, pre-mod. Center-bottom hits about 52C before settling down to 40-45C. The rest of the wheel peaks at 44C and settles to mid-30s.
New wheel with 2.2k mod resistor. Bottom-center peaks 63C with 49 and 54C elsewhere, and settles to a minimum of 55C (47C and 43C elsewhere). Much (about 10C under the hands) hotter!
Be First to Comment